Полуприцеп с рабочей платформой

KÖGEL Multi Chassis, verstärkt, Bordwände

You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website.

Excerpt from the equipment list. Complete equipment list available upon request.

Chassis
* Regular ladder frame in lightweight steel construction with continuous crossmembers
* With extension of the chassis frame, coupling plate approximately 8 mm thick
* with a 2-inch drawbar eye according to DIN 74080 / ISO 337

Suspension
* Axle lift mechanism on axle 1
* Three-axle unit SAF INTRADISC
* with disc brakes Ø 430 mm
* ET 120 air suspension with approximately 180 mm of travel

Tires
* Wheels with internal sensors according to UN ECE R141
Bwedpfjzhzg Sex Akcjp
* 6-ply 385/65 R 22.5 UNIROYAL TH 50
* 6 steel rims 22.5 x 11.75
* Offset approximately 120 mm (ET 120)

Chassis components
* Mechanical fifth wheel coupling with compensating plate, approximately 24 t lifting capacity, single-sided operation on the right side in the direction of travel
* Storage box for: 10 side panels, folding corner posts, and rear gate, completely enclosed, protected against splashing water, and simultaneously serving as a side protection device
* 2 plastic toolboxes, waterproof, dimensions (internal) approximately 545 x 400 x 400 mm, installed at the rear, 1x on the left and 1x on the right

Brake / Air suspension system
* EBS system 2S/2M with stability program (includes ABS/ALB function)
* EBS socket ISO 7638, (without connecting lines)
* Parking brake as spring-loaded brake, external pneumatic connections as well as external EBS diagnostic connection via ISO 7638 socket
* WABCO EBS system
* Air suspension system including 1 raising and lowering valve, mounted on the left side in the direction of travel behind the axle unit, driving position is automatically engaged
* 2 fail-safe coupling heads at the front ISO 1728
* Air reservoirs for the braking system and air supply made of steel (EN 286-2)

Floor
* Plate floor approximately 30 mm thick, multiple-ply glued plywood
* Floor sealed around the perimeter
* Pocket profiles for square tube inserts approximately 80 x 80 mm
* Storage for a maximum of 14 square tube inserts approximately 80 x 80 (length 1,990 mm) on the front wall inside

Front wall
* Front wall approximately 2,000 mm high with steel corner posts, with profiled sheet steel, screwed/riveted to the frame
* 2 pairs of lashing points (permissible lashing force approximately 1,000 kg per ring) on the front wall according to EN 12640, Note: If the front wall is used for securing the load, suitable lashing straps must be used to tension the load, if the vehicle is operated without side panels and a rear gate.

Rear wall
* Folding rear wall approximately 600 mm made of aluminum hollow profiles with 3 tensioning anchors and T-handle locks
* 2 folding steps on the inside, folding steel corner posts at the rear in the height of the side panel

Side wall
* 4 pairs of folding corner posts in the height of the side panel
* VarioFix steel outer frame with holes
* 4 pairs of corner post holders for folding corner posts on the outer frame (evenly distributed)
* 24 pairs of lashing eyelets in the outer frame (according to EN 12640), permissible tensile force approximately 5,000 kg per ring

Side panels
* 5 pairs of folding side panels approximately 600 mm made of aluminum hollow profiles with tensioning anchors

Electrical system / Electronics
* Lamp carrier made of steel, located above the underrun protection
* KÖGEL LUXIMA Premium package, consisting of: LED

Объявление было переведено автоматически. Возможны ошибки перевода.