Трал низкорамный

Meusburger 2-Achs-Jumbo-Tiefbett mit Planenaufbau

Chassis:
- Steel frame welded construction with front and rear frame extensions and a low-bed without a rear slope
- Frame neck + kingpin plate 225 mm
- Low-bed designed for a point load of 25 tons over 5 m
- Outer frame closed on the outside with welded lashing rings for securing cargo
- Interchangeable 2" kingpin
- Rear mounting rail for aluminum ramps

Axles and Tires:
- BPW low-loader axles, 10 tons axle load each, air spring diameter 360 mm
- Air suspension with lifting and lowering device, stroke 220 mm (-60/+160 mm)
- Wabco SmartBoard with ECAS function for 2 coupling heights + 100 mm
- S-cam brake 300/200 mm, asbestos-free brake linings
- Automatic slack adjusters
- IVTM tire pressure monitoring system
- 9 tires 235/75 R 17.5, tubeless

Steering:
- 1st and 2nd axles hydraulically steered via the fifth wheel coupling

Floor:
- Multi-layer glued panel floor with a thickness of 27 mm, flush with the outer frame and longitudinal beams
- Reinforced underneath with GRP coating
- 12 pairs of lashing rings welded into the outer frame (8 pairs RUD 8 tons – 6 pairs in the low-bed and one pair each on the gooseneck and at the front of the rear section – 2 pairs of lashing rings 4 tons on the gooseneck and rear section)
- 6 pairs of mushroom-shaped load securing points in the outer frame in the low-bed
Pgodpoiu Eu Njfx Agtjp
- Storage compartment with lid in the floor of the low-bed, front left and right

Front Wall:
- 25 mm aluminum hollow profiles extending up to the lower edge of the roof with integrated tarpaulin tensioning device

Sliding Tarpaulins:
- Sliding tarpaulins on both sides with welded vertical and horizontal straps (spacing approx. 600 mm) and stainless steel tensioning closures
- Adjustable tarpaulin straps (over center) up to a loading width of 4,000 mm, including tarpaulin extension with snap buttons and Velcro
- Tarpaulin extension in the direction of travel: 300 mm, in height: 750 mm
- Incl. eyelets for a loose tarpaulin extension part
- 1 pair of vertical tarpaulin pockets with a length of approx. 1,000 mm, position in the low-bed at the front extension
- With strap pockets

Rear Wall:
- Steel rear portal frame with lateral tarpaulin mounting device
- Aluminum double-wing door, 25 mm thick
- Both door wings can be fully folded in with door latch
- One aluminum double-hinge hinge and two recessed handle recesses per door wing

Front Corner Posts:
- At roof height, screwed on at the front end

Intermediate Posts:
- 3 pairs of steplessly adjustable folding posts
- The posts can be moved along the entire length using roller carriages
- Intermediate posts can also be fixed in the rear platform in the low-bed

Roof:
- EDSCHA sliding tarpaulin (galvanized) with crossmember that can be moved in both directions (pushed forward together in the loading area)
- Rear portal crossbar can be swung out
- PVC tarpaulin roof without customs closure
- Manually hydraulic lifting roof on both sides, stroke 450 mm
- Lifting roof can be operated in the front (9x50) and rear (9x50) elevated positions
- Including tarpaulin extension and tarpaulin rail at the rear
- Tarpaulin can be extended by 900 mm at the front end wall

Accessories:
- Extendable warning signs (removable at the rear and front with socket) incl. position lights up to a loading width of 4,000 mm
- Storage of the 4 warning signs on the front wall, inside, top right and left
- 1 aluminum ladder with bracket 2,500 mm long on the front wall
- 2 rows of aluminum slats self-locking
- Sheet metal mudguard

Объявление было переведено автоматически. Возможны ошибки перевода.