Полуприцеп-платформа

Faymonville MAX Trailer 3-Achs-Doppeltele-Plateau zg

You receive a current & complete inspection and function report with every used trailer.

Loading area:
-Loading area in extendable design with pneumatically operated locking mechanism
-There is an approx. 250 mm wide fixed intermediate table on the middle carrier
-8 pairs of lashing rings can be folded outwards (LC 5,000 daN)
-3 pairs of lashing rings can be folded outwards (LC 10,000 daN)
Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN)

Axles and tires:
-PW axles and suspension, all axles with hydro-mechanical forced steering
-Disc brakes, technical axle load: 9,000 kg
-Air suspension with lifting and lowering valve
-axle tool
-6 tires 385/65 R 22.5

Brake system:
-brake system in accordance with EU regulations with EBS-E (2S2M)

Seat posts:
-JOST seat posts (mechanical) with 2-speed gearbox for 24 tons lifting load (50 tons test load)

Accessories included:
-One bracket for the warning signs on the gooseneck and on the rear plate on the left and right, including socket
-Reverse steering can be operated from the front and rear by cable remote control via pushbuttons, with tracking control of the axles
-Electric hydraulic unit
-4 wheel chocks with holder on the front wall
-2" kingpin
-One galvanized steel bulkhead approx. 2,200 mm high
-Yellow-red air couplings on the galvanized connection strip at the front
-White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear
-European reflector plates (red/yellow) at the rear of the trailer
-One mud flap at the rear of the trailer
Gxc808Q
-Manual and description
-One bracket for a rotating beacon at the rear of the trailer
-Loading area with approx. 30 mm thick wooden floor edged in omega profiles
-10 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed
-6 pairs of WADER container pockets in the cargo bed, for 1x 20ft container, 2x 20ft containers or 1x 40ft container, an additional locking point is provided in the pull-out for a 45ft container
-A layer of sand painted onto the central beam to prevent slipping
-5 pairs of stanchion pocket rails, mounted transversely in the loading area, for 100 x 50 mm stanchions
-One galvanized bracket transversely under the cargo bed approx. 2,390 x 720 x 400 mm
-a ladder mounted on the right in the direction of travel
-One toolbox 1,200 x 500 x 480 mm at the front under the cargo bed on the left in the direction of travel
-Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status
-Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease and removable protection around the pump
-Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver as single-track control
-Four warning panels, extendable by approx. 400 mm, approx. 423 x 423 mm with a position lightA holder for rotating beacon on the warning panels
-2 reversing lights mounted on the rear panel
-Speed sticker 80 km/h at the rear and on both sides
-Load manometer to determine the axle loads including load diagram
-HRM metallization (High Resistance Metallization) of the outer frame
-Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Объявление было переведено автоматически, в связи с чем могут иметь место некоторые ошибки перевода.