Сменное шасси

Hangler LKW Tieflade Liftmaster Aufbau für 3 Achs LKW Fahrgestell zum Transport von Arbeitsbühnen

Additional Information
Frame
Steel welded construction made of fine-grained steel, hot-dip galvanized, flat platform without edge reinforcement,
the loading area slopes downwards by approx. 8° after the rear axle. Longitudinal beams made of steel profiles,
steel frame hot-dip galvanized, with a stainless steel plate at the bend as a cable guide - flush with the floor. For trucks with
wheelbase: 2nd axle 5,100 mm / 2nd to 3rd axle 1,350 mm
Trailer hitch
Trailer hitch ball head D24.8:, trailer load 2,800 kg,
incl. mounting and electrical system with 7-pole socket
Accessories/Conversions
2 holders for wheel chocks, aluminum side impact protection, foldable - to be taken over from the truck!
Steel under-run protection, quarter-shell mudguards with mud flaps - to be
taken over from the truck!
Storage box
Plastic toolbox, with drawer and insert, w=650 / h=520 / d=670 mm, lockable with a padlock. (Lock not included)
1 bracket for 3 x petrol cans
1 stainless steel storage box, w=600/h=400/d=500 mm, with a polished door, incl.
lockable, contains control valve and electro-hydraulic
pump unit. Control box with all-round door seal and
sealing collars on the back (splash-proof according to technical
possibility)
Electrical system
Adjustment of the existing tail lights, 2 additional LED work lights, recessed in the front panel
switched via parking lights with a switch on the front panel, outside on the front left, 1 LED
work light,
at the rear, with integrated rear view camera Incl.
with color flat-screen monitor, screen with suction cup holder and power supply via 24 volts,
voltage converter 24/12V, 1 7-pole 12V socket = adapter plug
Floor
Mega Grip made of interlocking, galvanized grating, steel grating 50/4 Incl.
with a mesh size of 50 mm. Top side with anti-slip interlocking,
running continuously over the entire main frame platform
Tie-down rings
12 pairs of tie-down rings in the outer frame, freely pivotable - 10 tons each.
1 x at the very front and the last one at the very back. 1 tie-down ring at the very back in the middle for attaching the
winch cable
12 tie-down rings recessed in the middle of the floor, 5 tons each
Front panel
Front panel made of steel sheet, height 1,500 mm. Fixed with corner pillars at the height of the front wall. 2
x 12 lifting brackets for tie-down chains, mounted on the left and right on the front panel
Winch
Electric winch, 24 volts, pulling force approx. 6350 kg, mounted in the middle on the front panel, operated with a remote control, cable length min. 35 m x 9.5 mm, with cable window,
with cable pressure plate, incl. overload protection, cable free-running coupling, hand switch with approx. 5 m
control lever, acceptance of the winch, civil engineer's test report, test book, operating instructions
Ramps
Length 3,500 mm - 2-part (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg / pair, electro-hydraulically foldable and laterally movable - incl.
electro-hydraulic pump unit. Ramp angle approx. 8° with the rear axle lowered
Ramp support made of steel grating, hot-dip galvanized, with
anti-slip interlocking. Ramps can be slid together to approx. 170 mm,
Hsdpfx Asi Riytepmsp
ramp extension hydraulically. Ramp prepared for operation on a loading ramp with full load capacity.
Ramp locking with 2 lashing straps.
Ramp tip offset (nose min. 150 mm) suitable for resting on loading ramps.
Labeling of the ramp operation.
Lowering brake valve for lowering the ramp
Support
Adjustable support legs, foldable at the rear + length adjustable,

Объявление было переведено автоматически. Возможны ошибки перевода.