Прицеп с рабочей платформой

MÜLLER-MITTELTAL 4-achs Anh. Tieflader, Klapprampe, Gummibelag

T 4 Profi 40.0

----Brakes:

* Wabco EBS-E (electronic braking system)
* Emergency release system for spring-loaded cylinders
* Drum brakes

----Axles:

* 4 x 11-ton Gigant axles

----Suspension:

* Air suspension with lifting and lowering system and RtR valve

----Drawbar:

* Straight drawbar with 50 mm drawbar eye and stepless height adjustment

----Electrical System / Lighting:

* Tire pressure monitoring system with display option in the truck display via EBS signal - without truck-side installation -
* SmartBoard as an information tool with pressure sensors for axle load display per axle group
* 15-pin power connector
* LED rear lights
* LED marker lights (removable) at the rear
Dedpfoylfvgex Ahzekp

----General Components:

* Warning sign packages at the front & rear
* 2 x toolboxes made of galvanized, powder-coated steel sheet, approx. 650 x 300 x 600 mm, on the right side
* Closed plastic fender at the front
* Straight steel mudguards at the rear, each with splash protection (spray mist suppression)
* Lateral impact protection

----Low-bed Platform:

* Extension of the turntable platform by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and locking mechanism
* Floor over the turntable platform made of 50 mm needlewood, and in the low-bed platform made of 60 mm needlewood
* Rubber coating 20 mm instead of wooden floor in the running area with a low-bed length of 6,780 mm including the access ramp
* Rubber coating on the access ramp, left and right, approx. 860 mm long
* 4 lashing eye pockets on each side (however, no lashing bars included) with simultaneous 2-ton lashing capability

----Chassis:

* Chassis made of high-strength fine-grain steel

----Load Securing (Lasi - Package):

Turntable Platform:

* 2 pairs of 13.4-ton lashing eyes in the outer frame of the turntable platform

Low-bed:

* 4 pairs of 10-ton lashing eyes on each side of the outer frame, retractable and loadable in all directions
* 2 pairs of 13.4-ton swiveling lashing eyes on each side at the rear

----Ramps:

* Rubber coating on the folding access ramps
* Hydraulic folding ramps with hydraulic extendable front section, approx. 4,650 x 720 mm
* Hydraulic lateral ramp adjustment & load holding valves

----Rear Support:

* Hydraulic rear support

----Width Extension:

* 8 pairs of galvanized folding outriggers for 3 m overall width (however, not in the rear slope)
* Width extension boards stored in a compartment on the left side

----Excavator Arm Rest:

* Excavator arm rest above the rear axle to the end of the access ramp, approx. L=2,100 mm x W=740 x D=190 mm
* 2 pairs of 6.4-ton lashing eyes on the side in the excavator arm rest

----Hydraulics:

* Hydraulic flow divider in the trailer (with hydraulic pump output in the truck of over 40 - max. 120 l/min.)

----Loading Dimensions:

* Rear loading area: approx. 6,780 x 2,520 mm (incl. 860 mm access ramp)
* Loading area above the turntable: approx. 2,990 x 2,520 mm

----Loading Height:

* approx. 890 mm, +/- 20 mm

----Painting:

* Reflective contour striping on the sides and at the rear
* Chassis, turntable, access ramps, and folding outriggers hot-dip galvanized
* Axles, drawbar, air tanks, and turntable painted in a black color

----Information:

* New vehicle with manufacturer's warranty
* Subject to errors and prior sale

----Delivery Time:

* Immediately available from Egestorf

Объявление было переведено автоматически. Возможны ошибки перевода.